Stance

NABOSO: FEEL THE FORCE

To Dr. Emily Splichal

In recognition of Dr. Emily Splichal’s contribution to my knowledge and through the knowledge gleaned from the use or her pioneering NABOSO surface science technology I am dedicating this post to her as my teacher, mentor and inspiration. Thank you Dr. Splichal.


In this post I am going to discuss how NABOSO surface science technology gave me the feedback mechanism to confirm the optimal ramp angle I needed to transition to a higher level of skier performance.

Optimal Ramp Angles starts with Stance Training

My transition started with refinements to my stance that came from incorporating Dr. Splichal’s principles of foot-to-core sequencing (that connects the feet with the pelvic core) and body fascial tensioning (that unifies the body). Prior to these changes my stance is what I would now define as good but not optimal. The huge improvement resulting from the refinements served as the impetus for a series of posts on the sequencing process required to assume a fascially tensioned stance with foot to core sequencing. I called this the SR Stance. The reason I chose this name was to draw reader attention to the stance posts by making the stance seem innovative, but not intimidating.

KIS is the Stance Kiss of Death

In reviewing material on ski technique, a skier’s stance is described as anything from an athletic stance, a relaxed stance, a ready stance, a balanced stance, a centered stance or a whatever feels good stance. A focus on selling skiing as easy with the KIS principle (Keep It Simple) has resulted in stance being perceived as less than critical to good technique. This leaves most skiers with the impression that a ski stance should feel similar to a relaxed upright stance on two feet with weight equally distributed between both feet and the heels and forefoot of each foot. This is interpreted by skiers as meaning they are balanced or in balance. So it follows that in actual skiing there should be even ‘pressure’ everywhere with no sensation of pressure on any specific area of the foot.

If I ask a typical skier to stand on a ramped surface and assume their ski stance they will find the sweet spot where their weight feels evenly distributed and identify it with their ski stance regardless of the  angle of the surface

So the first challenge to transitioning to a higher level of skier peformance is accepting that a strong ski stance must be learned and consistently rehearsed by doing drills as I do every time I go skiing. It’s like pre-flight check. NABOSO provide the conscious and subconscious CNS feedback that tells me when I am cleared for take off.

The NABOSO Effect

In my post NABOSO PROPRIOCEPTIVE STIMULATION INSOLES, I stated that the principle proprioceptive neural activity associated with balance responses occurs across the plantar plane. It is strongest in the 1st MPJ (big toe joint) and big toe. The fast acting small FA II nerves in this area are activated by pressure and skin stretch both of which occur in the late phase of Mid Stance. Optimal ramp angle is critical because it maximizes both pressure and skin stretch thereby potentiating the sensory input required to initiate controlled movement.

Assuming a NABOSO is trimmed, if necessary, to fit a shoe, there will be a positive effect on plantar proprioceptive stimulation. But my experience to date has been that the plantar proprioceptive stimulation will be much more pronounced in a minimal, zero drop shoe with adequate width for fascial forefoot tensioning and correct alignment of the big toe.

The big breakthrough for me came after I started using NABOSO insoles in shoes with different heel raises (drops). It turned out that I had the highest perception of  pressure under the ball of my foot in late mid stance phase with shoes with zero ramp (drop). When I put NABOSO insoles in my ski boots to test them I could hardly perceive any pressure under the ball of my outside foot during skiing no matter how I adjusted my stance or the tensions in my boot closures. This told me that my ramp angle of almost 3 degrees was far too great. As soon as I reduced the angle to 1.2 degrees (which is what I tested best at on my dynamic ramp angle device) it is no exaggeration to state the the whole world changed. But the transition effect didn’t kick into high gear until this ski season after my brain had time to delete a lot of the bad programming from the old ramp angle.

NABOSO 1.0 on the left. NABOSO 1.5 on the right. I use 1.5 in my ski boots. I purchase the large size and trim to fit.

Tentative Conclusions

  • A system that provides continuous subconscious sensory input to the CNS with the ability to consciously sense sensory input during drills in executive mode is important.
  • Stance training should be incorporated into racer training programs at an early stage and optimal stance ramp angle identified and implemented.
  • Once optimal ramp angle has been implemented the boot should be set up to the skier’s functional specification which I will discuss in future posts.
  • Stance ramp angle should be retested on a periodic basis to confirm the requirements have not changed.
  • Adjustments should be made as soon as possible after the end of a competitive season and no further changes made during the subsequent competitive season.

In my next post I will discuss Dr. Splichal’s protocol for using NABOSO insoles and matts in training.


Disclosure

I am not involved in any form of business association or affiliation or any have business interest or investment with Dr. Splichal/NABOSO/EBFA. Nor do I receive any form of compensation from the sale of NABOSO. Prior to marketing her NABOSO insoles Dr. Splichal provided me with a small sample of NABOSO material at her cost to cut insoles from for testing.

 

 

LEARN THE SR STANCE IN 3 EASY STEPS

This post was originally published on October 23, 2016. I have revised the post to clarify that the SR Stance applies to the load phase of a turn that occurs in what is commonly referred to as the bottom of a turn and that the joint angles of the SR Stance are configured by the major muscles in isometric contraction. When external forces cause the muscles to lengthen or stretch this will trigger the myotatic or stretch reflex. Because the myotactic reflex is a spinal reflex it is activated in 1 to 2 thousandths of a second. As such, it is both rapid and powerful.


The SR Stance configures some of the most powerful muscles in the body in a state of isometric contraction so that the powerful myotactic stretch reflex can maintain the angles of the ankle, knee, and hip and keep the CoM of a skier in balance on their outside ski in the most powerful position in the load phase of a turn.

The SR Stance is best learned outside the ski boot in an environment where the feet and legs are free from any influences. One of the benefits of learning an SR Stance outside the ski boot is that, once learned, it provides a reference against which to assess whether a ski boot supports the functional parameters of the skier. If it doesn’t, the SR Stance can be used as a reference to guide equipment modification and establish when and if it meets the functional requirements of the skier.

The SR Stance tensions the pelvis from below and above; below from the balls of the feet through the PA-soleus-gastrocnemius-hamstring muscles to the pelvis and above from the shoulders-latissimus dorsi-trapezius muscles to the pelvis.

The graphic below shows the Achilles Tendon junction with the PA at the heel bone.

pa-ac

The graphic below shows the 3 major muscles of the leg associated with the SR stance.

3-muscles

The Soleus (left image in the above graphic) extends from the back of the heel bone (see previous graphic) to a point just below the knee. It acts in concentric contraction (shortening) to extend or plantarflex the ankle. In EC-SR, the Soleus is under tension in stretch in isometric contraction.

The Soleus is one two muscles that make up the Triceps Surae.

The Gastrocnemius (center image in the above graphic) extends from the back of the heel bone  to a point just above the knee. It acts in concentric contraction (shortening) to flex the knee. In EC-SR, it is under tension in isometric contraction to oppose extension of the knee.

The Hamstrings (right image in the black rectangle in the above graphic) extends from a point just below the knee to the pelvic girdle. It acts in concentric contraction (shortening) to flex the knee. In EC-SR, it is under tension in isometric contraction to oppose extension of the knee.

A number of smaller muscles associated with the SR that will be discussed in future posts.

The graphic below depicts the 3 steps to learning an SR Stance.

er-steps

  1. The first step is to set up a static preload on the shank (shin) of the leg by tensioning the soleus muscle to the point where it goes into isometric contraction and arrests ankle dorsiflexion.

The static preload occurs when the tension in the soleus muscle of the leg simultaneously peaks with the tension in the sheet-like ligament called the plantar aponeurosis (PA). The PA supports the vault of the arch of the foot. The soleus is an extension of the PA. This was discussed in my post ZEPPA-DELTA ANGLE AND THE STRETCH REFLEX.

  • While barefoot, stand erect on a hard, flat, level surface as shown in the left hand figure in the graphics above and below. The weight should be felt more under the heels than under the forefoot.
  • Relax the major muscles in the back of the legs (mainly the hamstrings) and allow the hips to drop and the knees to move forward as shown in the right hand figure in the graphics above (1.) and below.
  • As the knees move forward and the hips drop towards the floor the ankle joint will dorsiflex and the angle the shank forms with the floor and the angle of the knee, will both increase until a point is reached where the shank stops moving forward on its own. Movement of the shank will probably be arrested at a point where a plumb line extending downward from the knee cap ends up slightly ahead of the foot. This is the static preload shank angle. It is the point where the soleus and quadriceps muscles go into isometric contraction.

static-preload

2. From the static preload shank angle, while keeping the spine straight, bend forward slightly at the waist. The angles of the shank (ankles) and knees will decrease as the pelvis moves up and back and the CoM moves forward towards the balls of the feet. This will cause the muscles of the thigh to shift from the Quadriceps to the Hamstrings. Bending at the waist tilts the pelvis forward. As the pelvis tilts forward, it tensions the Hamstrings and Gastrocnemius causing the knee and ankle to extend to a point where extension is arrested by the muscles going into isometric contraction. Tension in the Hamstrings and Gastrocnemius extends the lever arm acting to compress the vault of the arches of the feet from the top of the shank to the pelvis thus increasing the pressure on the balls of the feet through Achilles-PA load transfer.

3. From the position in 2., round the back and shoulders as you bend forward from the waist.

Shldrs-back

Make sure the core is activated and tightened as you round the back and shoulders. Pull the shoulders forward and towards each other as the back is rounded so as to form a bow with the shoulder girdle. Looking down from above, the arms should look like they are hugging a large barrel.

Repeat steps 1 through 3. Pay close attention to the changes in the sensations in your body as you work through each step. If you bounce up and down lightly in the position in Step 3., the angles of the joints in your stance should return to the static preload position between bounces.

With the ski boot and Zeppa-Delta ramp angles configured to enable an SR stance, your ski boots will work for you and with you instead of the other way around.

In my next post, I will go into greater detail on how rounding the shoulders and holding the arms in the correct position optimally activates the muscles associated with the SR stance.

RAMPING UP THE POWER OF YOUR STANCE

Note to the reader

The post that follows was originally published on March 1, 2016. At the time that I wrote it, I was trying to identify the optimal net (total) ramp angle or NRA using fixed angle ramps. But I found the process to be inconclusive for reasons I give in my recent posts on the dynamic ramp assessment device. I am reposting this older post because many of the concepts expressed are even more relevant in view of the results seen with the dynamic ramp assessment device and boot boards altered to the same ramp angle identified in dynamic testing.


RAMPING UP THE POWER OF YOUR STANCE

The foundation of a strong technique is a strong stance. But what makes a strong stance? The angle of the combined ramps of the binding and boot board or zeppa in relation to the base of the ski. If the net ramp angle weren’t important, binding and boot makers would make their products with no ramp. If ramp angle doesn’t make a difference, why bother? But not only does net ramp angle make a difference, it has a significant effect on stance.  Stance affects balance and muscle power, especially the ability of eccentric gastrocnemius-soleus complex muscle contraction to absorb shocks that would otherwise be transmitted up the leg to the knees and back. I discussed some of these issues in WHAT’S YOUR ANGLE? – : https://skimoves.me/2014/03/29/ski-boots-whats-your-angle/ ‎

If there were a problem, and there is, the ski industry is all over the place especially when in comes to binding ramp. There doesn’t appear to be any industry standards and especially any continuity between products. Worse, most skiers assume that their ski boots are putting them in the optimal stance. Without a reference they have no way of knowing. The Stance Ramp can give them that reference especially when it comes to how much ramp is enough, how much ramp is too much and how much ramp is too little.

Note Added March 19, 2018 – Having a kinesthetic sense of a stance based on tensegrity gives a skier a valuable tool that when used in a structured process can help them assess the effect of zeppa-delta ramp angle and the constraint imposed on their feet and legs by the structures of a ski boot.

In 1978, when I was building boots for female racers with small feet, I noticed that they were skiing like they were wearing high heel shoes. When I started checking their bindings and boot board ramps, I found out why. Some had 10 or 12 degrees or more of net ramp angle. After I started doing stance training with racers on a ramped board I discovered through empirical experiments that about 3 degrees of ramp angle seemed to give skiers the strongest stance.

Note Added March 19, 2018 – It now appears as if 3 degrees is the upper limit of the zone of stability. This explains why skiers started to ski better when the net ramp angle approached 3 degrees.

I didn’t really understand why until much later. Was the process scientific? No, not at all. Do studies of this critical issue need to be done? Absolutely. If I figured out that ramp angle was a critical issue almost 40 years ago, why is it that no studies appear to have done in the intervening years to determine the affects of ramp angle and identity the optimal angle?

With input from skiers in different parts of the world over the past two years, I have narrowed the ideal ramp angle down to about 2.7 degrees. This seems to be something of a standard in World Cup. Through experiments over the past few months, I have found that changes of 0.1 degrees can make a significant and easily perceivable difference. Optimal ramp angle isn’t just critical for World Cup racers, it is critical for all skiers. The easiest way to convince yourself of the importance of optimal ramp angle is for you to experience the effects of ramp angle through experimentation. How? With a Stance Ramp set to a base reference angle of 2.5 degrees.

The Stance Ramp lets skiers stand in their ski stance (barefoot is best) on a flat, level, surface then assume the same stance on the Stance Ramp, compare the kinaesthetic sense and judge whether they feel stronger of weaker. The angle of the Stance Ramp can be predictably increased or decreased by inserting shims at either end between the ramp and the surface it is supported on. When the ramp angle that makes the stance feel the strongest is arrived at, it can compared to the ramp angle of the ski boot board by having one foot on the Stance Ramp and the other in the ski boot.

The best part? The Stance Ramp is easy and inexpensive to make with readily available materials. I made mine out of some scraps of plywood I had lying around. Here’s what the Stance Ramp I made looks like. You stand with one foot on either side of the stiffener in the center with your heels at the high end (left end in the photo below).

IMG_6304

Here’s a top (plan) view. It is a good idea to check the surface the ramp will sit on to make sure it is very close to level.

IMG_6302

Here’s the underside of the Stance Ramp showing the element at the rear that gives the ramp its 2.5 degree angle. The stiffener in the center is important to ensure the ramp doesn’t flex under your weight.

IMG_6309

The sketch below is a basic plan for a Stance Ramp. The only critical details are the height or thickness of the element that lifts the rear aspect of the ramp to achieve and 2.5 degree angle (angle A) and the distance the lift element is placed from the front edge of the ramp. The stiffening element in the center of my ramp is 8 cm wide. The ramp has to be big enough to stand with the feet under the hips and long enough to accommodate the length of the feet.

Stance Ramp

An online right angle calculator such as the one at cleavebooks.co.uk can be used to calculate the spacing of the lift element from the low end (front edge) of the ramp based on its thickness.

SR calculate

Once the optimal ramp angle is arrived at, the Stance Ramp can be used in combination with the ski boot shell to confirm that the boot board is at the same angle.

IMG_6307

In my next post, I will discuss what I call the Resistive Shank Angle that is the base to build  a strong stance on.

ISOMETRIC STANCE MUSCLE TENSIONING SEQUENCE

Tensegrity

Tens(ion) + (Int)egrity 

The optimal ramp angle, as determined by the dynamic ramp device, is based on a stance predicated on the principles of Biotensegrity.

Fascial continuity suggests that the myofascia acts like an adjustable tensegrity around the skeleton – a continuous inward pulling tensional network like the elastics, with the bones acting like the struts in the tensegrity model, pushing out against the restricting ‘rubber bands: Tom Myers, Anatomy Trains (1.)

A ski stance based on the principles of bio-tensegrity must be learned and rehearsed in a step-by-step process. It is neither natural or intuitive although elite skiers and racers such as Shiffrin and Hirscher appear to have acquired the elements of Biotensegrity. Assuming a group of racers of equal athletic ability, the odds will favour those whose stance is based on Biotensegrity.

In a ski stance based on bio-tensegrity, tension in the arches of the feet extends to from the balls of the feet to the palms of the hands holding the poles.

  1. Start by standing barefoot on a hard flat floor or surface in a controlled environment such as your home. Where possible, use the same surface and place to rehearse the stance. If you have constructed a dynamic ramp assessment device, use this with the top plate set to level.
  2. Stand upright at attention. You should feel most of the weight under your  heels and less weight across the balls of your feet. This is normal. The fore-aft weight distribution is actually 50-50 heel to forefoot. But because the weight of the body is spread across the balls of the feet and along the outer aspect behind the small toes, more weight is sensed under the heels. Stand so your weight is distributed equally between both feet.
  3. Relax your hamstrings (in your thighs) and let your torso drop towards the floor.  Your knees will move forward as they flex and your ankles will dorsiflex. Your ankles should stop dorsiflexing on their own when the front of your knee caps are aligned approximately over the balls of your feet. This is the point where the tension in your soleus (calf muscle) peaks with the tension in plantar ligament of your arches. You should feel about the same pressure under the balls of your feet as you feel under your heels. But it should feel as if the circle of pressure under your heels has gotten bigger and your feet are more connected or integrated with the floor. I call this ‘rooted’ because it should feel as if your feet have sunk into the floor.
  4. While keeping your upper body erect, move slightly forward in the hips. You will quickly reach a point where you start to become unstable and feel as if you would fall forward onto your face if you moved farther forward in the hips. When you get to this point your big toes should press down on the floor on their own to try stabilize you. This is the forward limit of stability.
  5. Now move rearward in the hips until you start to feel the same instability. This is the rearmost limit of stability.
  6. Now bend forward from the waist. Do not curl your back. Bend from the hip sockets for the thigh bone (femur). This movement is actually thigh flexion. Lift your thigh to get the right feeling. As you bend forward from the waist, your buttocks will move rearward and upward as your ankles and knees straighten.  Reach forward with your arms as if you were going to hug a large barrel in front of you. Make sure the palms of your hands are facing each other with fingers curled and pointing towards each other.
  7. Find the place where your arms and head feel neutral to your spine. As your arms come into position you should feel your abdominal core and muscles in your back acquire tension. Slings Isometric stance
  8. Experiment by moving forward and rearward in the pelvis. As you move forward in the pelvis the pressure should increase under the balls of your feet. But you should not feel unstable. If anything, you should feel stronger and more stable. You should feel as if the weight of your head and shoulders is pressing your feet down into the floor.
  9. Increase the bend at your waist while keeping the pressure on the balls of your feet and heels until the top of your head is down by your knees. You should still feel very strong and stable in the feet. This is the lowermost limit of waist flexion.

Once you have acquired a kinesthetic sense of the bio-integrity of foot to hand tension, a sense of stability while pulsing the torso vertically up and down over the feet confirms a state of bio-tensegrity.

The photo below is of simple model I designed and constructed in 1993 to illustrate the basic concept of bottom up Biotensegrity and how the degree of passive tension in the plantar ligament of the arches of the feet and the vertical biokinetic chain is driven by the compression from weight of COM stacked over the foot.

The graphic below shows the continuum of tension from the balls of the feet to the opposite shoulders through the mechanism of the oblique posterior sling.

In my next post I will discuss what I term the NABOSO Effect.


  1. https://www.anatomytrains.com/fascia/tensegrity/

FIFTH GENERATION STANCE RAMP ASSESSMENT DEVICE

Since my first version of the stance ramp assessment device I have made a number of significant improvements. The series of photos below are of the fifth generation device.

The bottom plate or base of the device is approximately 18 inches (46 cm) wide by 16 inches (41 cm) deep (front to back). I intend to make the next version about 22 inches (56 cm) wide by 18 inches (46 cm) deep. Size is not critical so long as the top plate is deep and wide enough for the feet being tested.

Stiffness of the plates is critical. Three quarter inch thick (2 cm) plywood or medium density fiberboard (MDF) are suitable materials. I added 1.5 inch x 1.5 inch wood reinforcing ribs on the sides, middle and rear of the top plate.

The photo below shows the heel end of the device. Two 1/4 inch drive ratchets turn bolts threaded into T-nuts in the top plate that raise the heel end up.

The photo below shows the top plate hinged to the bottom plate with 4 robust hinges.

Four telescoping hard nylon feet are set into the bottom plate to enable the device to be leveled and made stable on the supporting surface. It is important that the device not tilt or rock during testing.

The photo below shows the details of the interface between the top plate on the left and the bottom plate on the right.IMG_3409

I used gasket material purchased from an auto supply to shim the forefoot of my boot boards to decrease the ramp angle so as to obtain the 1.2 degree ramp angle I tested best at.Shim pack

The package contains 4 sheets of gasket material that includes 3 mm and 1.5 mm sheet cork and 2 other materials.Gasket

I cut forefoot shims from the 3 mm cork sheet as shown to the right of the boot board in the photo below.BB w shims

I adhered the shims to the boot board with heavy duty 2-sided tape and feathered the edges with a belt sander.shims installed

I corrected the ramp of my boot boards in 3 stages. Once my optimal ramp angle is confirmed, I will pour a boot board into the base of my ski boot shells in place of the existing boot boards using a material such as Smooth-Cast 385 Mineral Filled Casting Resin. More on this in a future post.

Ramp Angle Appears to User Specific

It is important to stress that although there appears to be a trend to optimal boot board ramp angles for elite skiers in the range 1.5 degrees or less, there is no basis to assume a  ramp angle that is optimal for one skier will be optimal for another skier. Recreational skiers are testing best between 2.0 and 2.5 degrees.

It is also not known at this point whether the initial optimal ramp angle identified with the device will change over time. Based on the impressive results seen so far in the limited number of skiers and racers who were tested and ramp angles adjusted there is no basis to assume that ramp angle is not a critical factor affecting skier balance and ski and edge control. Studies on this issue are urgently needed and long overdue.

It is important that testing for optimal ramp angle be preceded by kinesthetic stance training. This will be the subject of my next post.

A DEVICE TO DETERMINE OPTIMAL PERSONAL RAMP ANGLE

This post contains the most important information I have ever written on skiing. It concerns the important discovery I have made since I began to cast a critical eye on the positions of the various experts about 45 years ago; a method to determine the optimal personal ramp angle of a skier/racer.

By 1978, subjective experiments had taught me that a total ramp angle between the sole of the foot and the base of a ski of more than 3 degrees could have significant adverse effects on skier stability, balance and the ability to control the direction and especially the edge angle, of a ski. Wherever possible, I tried to limit total ramp angle (boot boards + bindings) to below or close to 3 degrees. But ski boot and binding construction often limited my ability to reach this objective. It was limitations in the construction of my current Head World Cup boot that presented challenges in getting the boot board ramp angle below 3 degrees. Through a concerted effort I had managed to reduce ramp angle to 3.3 degrees (bindings are zero) with a noticeable improvement in balance, ski and edge control. But the results of my recent NABOSO insole test suggested that the boot board ramp angle needed to be a lot lower.

The Dynamic Ski Stance Theory

A standard test of the human balance system is to subject a subject to dynamic changes in the platform under their feet. Over the past few years, I made numerous attempts to find the optimal ramp angle for skiing. One method involved assuming my strongest stance on a hard, flat level surface then stepping onto a plate shimmed to a fixed angle then repeating the process with the plate shimmed to a different angle. The results were inconclusive. Every time I went back to the hard, flat level starting surface my balance system seemed to reset. I had to get the angle of the tilted plate well over 3 degrees before I began to sense obvious instability. This led to my positing of a theory that the angle of a plate that a skier is standing on needs to be changed as the skier goes through a stance protocol designed to test stability and what I call a rooted or grounded connection where the skier feels as if their feet are literally rooted in the snow.

Research is Urgently Needed

Before I go any further I want to stress that I believe that an idea, no matter how compelling, is nothing more than a theory until it has been thoroughly tested and has withstood rigorous scrutiny. Even then, no theory should be immune to challenges. Research on this subject is urgently needed and long overdue. With this in mind, I designed the dynamic stance assessment device so it can be easily made with reasonable skills and readily available, inexpensive materials. I have recently completed a 4th generation prototype to serve this end. But a much more sophisticated device can and should be made and used by academic researchers. A servo motor driven ramp with a data acquisition package is the preferred option.

Stance Training is Essential

In order to obtain accurate results with the dynamic stance assessment ramp it is essential that the subject being tested undergo kinesthetic stance training and follow a protocol during testing that is designed to help the subject assess the effect of changes in ramp angle. It is disturbing that few of the skiers tested so far have a kinesthetic sense of the elements of a strong stance. Most have never sensed a strong stance. Worse, no ski pro or coach has ever discussed this crucial aspect of skiing with them. It appears as if it is simply assumed that a skier will automatically find their optimal stance. I can unequivocally state that this is not the case.

Dynamic Stance Ramp Test Results

  • The majority of skiers tested so far were most stable at ramp angles between 2.0 and 2.5 degrees.
  • A number of skiers, myself included, were most stable at close to or under 1.2 degrees.
  • One skier was most stable at 1.6 degrees.
  • One skier appeared to be relatively insensitive to ramp angle until it was above 2.8 degrees.
  • After training, most skiers were sensitive to changes of 0.1 degrees.
  • No skier tested so far was stable over 2.8 degrees.
  • Adding NABOSO insoles further reduced the ramp angle.

I tested most stable at 1.2 degrees; 2.1 degrees less than my existing boot board ramp angle. In order to reduce the boot board ramp angle to 1.2 degrees, I had to raise the toe end of my boot board 9 mm and lower the heel 2 mm for a total reduction of 11 mm.

First On Snow Impressions

Walking in my ski boots with the corrected boot board ramp angle immediately felt different. But the huge impact didn’t come until I started moving over the surface of the snow on my skis. Then the whole world seemed to change. I had a huge deja-vu moment; one that took me back to the solid, stable feeling I had under my feet in my first low-cut leather plastic soled ski boots. It was then that I realized that it was the jacked up heels of my first all plastic, rigid shell ski boots 45 years ago that had destroyed my balance and confidence on skis. This is a big miss for the ski industry, one that should have been caught by those who promote themselves as the experts in skiing, but wasn’t. This miss has huge implications for skiers at every level and ability all the way up to the World Cup. A skier, but especially a racer with a sub-optimal ramp angle will revert to an unstable weight on the heels, back seat Defensive Stance in which the skier is incapable of recruiting the enormous power of the glutes and optimal sensorimotor processes.

First generation device in action. Ratchet socket wrenches raise the ramp by turning bolts set into T-Nuts on each end.


Digital SmartTool electronic level accurate to 2 decimal places


Fourth Generation Stance Ramp assessment prototype. Two x two wood stiffening elements added to the platform.

The skiing of those whose ramp angle has been optimized is elevated to a whole new level provoking immediate comments like the difference is ‘night and day‘. After my transformation, I now believe that until ramp angle is optimized, everything else is irrelevant and that no amount of footbeds, orthotics, cants, alignment or custom fitting can overcome the adverse affect of sub-optimal ramp.